TELEMAX Telescope steel manual

Youtube video instruction: Link

1. Montage Steel

a) Leave the handle in, only slide the thinnest (upper) segment approx. 15 cm.
b) Bring the black water hose out via the oval hole (which is at the top of the thinnest segment) via the other end (bottom stem).

2. Montage blue red brush

a) Turn the black corner adapter with the thick thread in the blue red brush.
b)Connect the 4 small black tubes of 10 cm to the gold -colored water nipples of the brush. Tip: You can keep the tubes briefly under warm water to make them easier slide the gold -colored water nipples. Couple the end of the tubes with the PY couples and only then connect them with the 2 remaining small black tubes of 10 cm on the PE coupling piece. See image 2.
c) Tighten the stainless steel screw so that the brush stays straight on the handle and cannot turn during use.

3. Montage black all -round brush

a) Turn the black corner adapter with the thin thread in the black all -round brush (note: this can go roughly, it should be).
b) Attach the PY coupling with 2 black 15 cm tubes to the 2 gold-colored water nipples of the black all-round brush.
c) Tighten the stainless steel screw so that the brush stays straight on the handle and cannot turn during use.

4. Telescope stem with brush attach to water source

Depending on your situation, there are 3 options:

a) Do you have an outside tap with a male Gardena connection? Then connect the water hose from the stem to the supplied female Oranje Gardena coupling.
b) Do you have a garden hose with female Gardena connection? Then mount the supplied gold-colored bullet connection on the black water hose.
c) Do you have a garden hose without a connection? Then mount the included male Gardena connection with wing clamp on your garden hose and connect the black water hose.

5. Soap dispenser

a) There are 2 couplings in the reservoir. Remove this from the reservoir.
b) At one of the screw threads of the soap dispenser you will see a small arrow/triangle, connect the male Gardena coupling to this.
c) The female Gardena coupling links you to the other side of the soap dispenser. Tighten them well.
d) Loosen the transparent reservoir of the soap dispenser and fill it with multishine or sunshine solar panel cleaner. Turn the reservoir on again.
e) Suppose, depending on the amount of contamination, the soap dosing with the black spin mechanism. Setting on the smallest round/ball is often a great dilution. Tip: first let the water run before opening the soap dispenser (otherwise the cleaning agent will run out pure).

6. Cleaning (painted) woodwork, plastic or other smooth surfaces at height

a) Use the blue red brush for flat surfaces and the black all -round brush for hard -to -reach surfaces and corners.
b) Pour Profa Clean Multishine purely into the soap dispenser.
c) Open the water tap and leave the soap dispenser on the water level. First, scrub the coarse dirt with only water and the brush of the surfaces.
d) Open the soap dispenser on the first round/ball. Spread the surface to be cleaned so that the product is distributed and can withdraw. As soon as the reservoir is transparent, the product is finished. Now scrub the surface to be cleaned. The dirt is weakened by withdrawing, making it easy to let go. Tip: Multishine may not dry so work part by part. Avoid cleaning in full sun.
e) Rinse well with clean water (so close the soap dispenser). Let the surfaces dry on the air.

7. Cleaning solar panels

a) Check 2–3 times a year whether your panels are ready for cleaning. You lose return if you do not regularly clean the solar panels. Tip: Clean your solar panels during rain! Rainwater is lime -free, works as a week and ensures lime -free rinsing. This is a nice alternative to osmosis water. N.B. Do not clean your solar panels in summer / hot weather i.v.m. The temperature of the panels and therefore the chance of cracking.
b) Switch off the electrical installation, do not touch any cabling.
c) Use the blue red brush that is intended for flat surfaces and solar panels.
d) Use profa clean solar panel cleaner in the soap dispenser.
e) Open the water tap and leave the soap dispenser on the water level. First, scrub the coarse dirt with only water and the brush of the surfaces.
f) Open the soap dispenser on the first round/ball. Spread the surface to be cleaned so that the product is distributed and can withdraw. As soon as the reservoir is transparent, the product is finished. Now scrub the surface to be cleaned. The dirt is weakened by withdrawing, making it easy to let go. Work part by part.
g) Rinse well. Let the solar panels dry in the air.

8. General tips

Just rest? You can let the telescopic stem rest on the floor without the water hose being put into trouble, that is possible because of the plastic support point with notch.
Didn't need the full length? The thinnest (upper) segments are less stable than the wide segments. If you do not need the full length, keep the thinnest segments put in, or choose if necessary. For not to extend these thinnest segments for more stability.
Do you feel play in the clip? When you close a clip and you still feel play in the handle, open the clip again and turn the adjusting screw under the rubber.

9. Tips for malfunctions

10. After use

Content package:

Telescope stem 7.2m or 10.8m
Blue red brush (application: flat surfaces and solar panels)
Black Allround Brush (Application: Hardly accessible surfaces and corners)
Black Waterslang 12m
2x black corner adapter
1x Female Oranje Gardena connection
1x black male gardena connection with wing clamp attached to female Gardena connection
Gold -colored bullet connection
6x Black Waterslangjes 10 cm
PY coupling already connected to 2x black water hose 15 cm
2x PY coupling loose
1x PE coupling
1x PU coupling (you do not need this; if your hose ever break this can be repaired)
Soap dispenser

If you have any questions after this, you can always send us an e-mail info@profaclean.nl.

We wish you a lot of cleaning pleasure!